I have upgraded to the CH C10 replacing the CH C1.2 DAC with X1 power supply.

Nordost QNET Switch powered by the Nordost QSOURCE LPS.

I am using a Nordost Odin Gold power cord for Nordost QSOURCE LPS that powers the Nordost QNET Switch and several Nordost QPOINT resonators.

I am using 2 of the Nordost Valhalla 2 ethernet cables. The first one connects between the QNET Switch and the Roon Nucleus Plus. The second is from the QNET switch to the CH Precision C10 DAC.

Nordost Odin 2 Balanced IC's from the CH Precision C10 DAC to the CH Precision L10 true monaural preamp.

I am now using the Shunyata Everest 8000 power distributor which has replaced the Shunyata Triton V3 in my system for my front end electronics. I use a Nordost Odin Gold power cord for the Everest.

I have the Shunyata DPC 6 V3 power conditioner for my computer based audio gear. I have my Nordost Qsource LPS plugged into the DPC 6 V3. 

This Odin 2 power cord is used on the outboard power supply for The Beat SE turntable. This is plugged into the Shunyata Everest 8000 power conditioner.

This is a new LT tonearm but now with an arm tube made from Magnesium instead of wood. It is a very significant upgrade in sonics. I plan to have my existing LT arm modified to have the Magnesium arm tube as well.

I have now replaced my wonderful Lyra Etna SL cartridge with the new Lyra Atlas SL Lambda cartridge. My previous experience was that the original Etna SL cartridge was the best sounding of all of the Lyra cartridges. But not any longer. I was fortunate enough to be able to compare the new Lambda versions of the Etna SL and the Atlas SL in my system and the Atlas SL Lambda is simply stunning to hear in my system. The new Lambda Etna SL is also wonderful and better than the original Etna SL, but the Lambda Atlas SL is superior in every way.

I am now using Nordost Odin 2 balanced IC's between the CH Precision P10 true dual monaural phono stage and the CH Precision L10 true dual monaural preamp.

I am using 2 of the CAD GC3 Ground Controls. One GC3 is used for signal ground with each of my CH Precision M10 amplifiers and the second GC3 is used for Earth Ground with my Rockport Arrakis external active crossover.

I am using the CAD Ground Control Reference (GCR) in my system. This is used for signal grounds for my front end components and the earth ground for my Shunyata Everest 8000 power distributor.

The new CH Precision L10 True Dual Monaural linestage has replaced my long time reference, the CH Precision L1 true dual monaural linestage. As good as the 4 box version of the CH L1 linestage is, The CH Precision L10 True Dual Monaural (4 box) linestage surpasses it in every audio parameter.

I am using two of the Nordost Odin Gold Power Cords to power the two CH Precision L10 external power supplies for my CH Precision L10 true dual monaural preamp.

I now am using the CH Precision M10 mono block amplifiers. I have 2 of these and I run them in their active bi-amplification mode. These have just replaced (11/30/2021) my wonderful CH Precision M1.1 mono block amplifiers.

I am using 4 of the Nordost Odin Gold power cords on my CH Precision M10 amps. Each CH M10 amp outboard power supply requires 2 power cords each with 20 amp IEC connectors.

I use a 9 meter run of Nordost Odin 2 XLR IC's from the CH Precision L10 true dual monaural preamp to the Rockport Arrakis 2 external crossover.

This is the active external crossover for the Rockport Arrakis 2 speaker. It takes the feed from the preamplifier and then splits the signal for the bass drivers and all of the upper frequency drivers.

I am now using a Nordost Odin Gold power cord on my Rockport Arrakis external crossover. This replaced the already great Nordost Odin 2 power cord.

I am now using 2 pairs of Nordost Odin 2 XLR IC's to connect the Rockport external crossover to the CH Precision M10 amplifiers.

I am using 2 pairs of Nordost Odin Gold speaker cables  to bi-amplify the Rockport Arrakis 2 speakers.

My speakers are the bi ampified version of the Rockport Arrakis 2 with the active external crossover.  I am driving the speakers with a pair of CH Precision M10 amplifiers run in active bi amplification mode.

I have 13 of the Furutech GTX/NCF outlets with the GTX outlet Frames and the 105D NCF Carbon Fiber outlet covers.

I have 3 of the HRS SXR audio racks. Each rack is a 4 shelf version and I am using M3X2 isolation bases with G7 footers. These racks and bases hold the majority of my front end components. For the SXR base that holds my Beat SE turntable, I have added the SXR solid brace insert.

I have 4 of the HRS SRX amp stands with the M3X2 isolation bases with G7 footers, These are for the power supplies and my CH Precision M10 amps.

I am now using Nordost Sort Kones under many of my components. I am using a combination of both the BC and TC sort kones. I am using them under all of my TotalDAC digital components - both DACs, the Outboard Reclocker, the Streamer, the Live Power supply, the D1 player and the NAS. I also use them under my Beat SE turntable outboard power supply (not the turntable itself) and my Rockport Arrakis external crossover.

I have added the Isonic ultrasonic RCM. This is a wonderful RCM. I can do up to 10 LP's at once. It doesn't dry the records - but that is simple to do on my Loricraft.

There are now 3 of these beautiful LP record cabinets that I commissioned a friend to build for me. Its so much easier to find the LP that I am looking for and to put it back than it was with more traditional shelves that I was using before.