Very impressed, especially with the Leedh volume control. No preamp needed.
Clarisys Minuet
Just installed on 8-29-23. replaced my beloved Focal Sopra 2's.
Rotel Michi 8
Just added these 140 lb. amps. Rated for 1800 watts per 4 ohm.
JL Audio F-113 Subwoofers (4) of them.
4 F-113's
AudioQuest Niagara 7000, (2) 1200, 1000
On my 3 dedicated lines for a total of 4 AudioQuest units. I have (2)1200 for my JL subs. 2 are in the back of the room and 2 in the front.
AudioQuest Niagara Power conditioners
ADD-POWR Sorcer X4
Great conditioner!
AudioQuest Dragon High Current 20A for My Niagara 7000 & Dragon Source
Using this power cord on my AudioQuest Niagara 7000 power conditioner. Quite impressive!
Added another Dragon Source to my Lumin X1
Critical Mass Systems Center Stage CM2,2M in both the 1.0 & 1.5 size footers. Total of 6 sets being used.
I now have 6 sets under my equipment and boy are they impressive.
Clarus Crimson Bi-Wire Speaker Cable
Infigo Cables USB, Signature 2 sets XLR cables
Entreq Silver Tellus
Silver Tellus used om my digital. Plus a DIY large box used on analog and two smaller DIY boxes used on each speaker.
EtherRegen Uptone Audio
AfterDark Queen Clock and Linear power supply
Combo
WireWorld Platinum 8 Ethernet
I didn't think an ethernet cable would improve the sound much, but with cable connected to my Ether Regen input from my modem even though I am sending the output via fiber to my Lumin X1, increased the sound quality presence. Quite impressive.
I didn't realize I inadvertently made a sale for Reno but if u have not purchased your new x350.8 I would love to work with you. I have been a Pass dealer since 2003.
Interesting... The Audio Magic has a crystal in them. But, mine thus far don't. I made mine out of 1/8" copper caps with a cone shaped copper insert glued inside.
The need fair bit of machining to get the bell shape. Any instructions on making them, i.e tools needed
FWIW, the HFT's may have some magic dust aka crystal bits in them behind the mesh. Not asking you to take one apart, but my daughter was playing the the HFTs and bluetack filling the concave area of the HFT.
I pull the tack out and saw which i think was a fine speck of a crystal like dot stuck on the tack.
Not sure if I have 40. I have the fuse chips on all of my fuses. I have several Power chips on my circuit breaker box and a few other places. And I also have the speaker chips and some cap chips on my PS Audio P10.
Ozzy Albertporter, I own the Eggleston Andra 2's not the Focals.
Sorry, occupied with holiday guests and not paying attention.
My offer still stands if I get blessing from Stillpoints. I think Ultra 5 is solid stainless steel and no harm would come by drilling and threading.
I don't like the adaptors for my application, the difference between 14MM and 1/4-20 is too great. For your 3/8"-16, Tbg (Norm) is probably correct and you would retain resale value if you needed to move them later.
Albertporter, I own the Eggleston Andra 2's not the Focals.
Tbg, the 3/8"-16 is what my speaker uses. I thought it would be better to just have a straight same size threaded stud from speakers through the Stillpoints. That is if the Stillpoints could be threaded to accept the 3/8"-16 thread.
I would have to drill additional hole into the Andras to accept the new 1/4" inserts. That would place them slightly away from the outer edges.
Ozzy, I cannot imagine that a 3/8" 16 would be any better than a 1/4" 20. I do know that four SP Ultra Five under speakers and amps are superior to three.
Albertporter, Thank you so much for the offer. My speakers use a 3/8"-16 thread. If you could tap the Stillpoints to be able to use the 3/8"-16 thread that would be great!
Assume you must get from 14MM to 1/4-20 for the Stillpoints. I have a shop that will drill and tap the Stillpoints for about $100.00 allowing the full size 14MM rod from Focal to be used as intended.