Very impressed, especially with the Leedh volume control. No preamp needed.
Clarisys Minuet
Just installed on 8-29-23. replaced my beloved Focal Sopra 2's.
Rotel Michi 8
Just added these 140 lb. amps. Rated for 1800 watts per 4 ohm.
JL Audio F-113 Subwoofers (4) of them.
4 F-113's
AudioQuest Niagara 7000, (2) 1200, 1000
On my 3 dedicated lines for a total of 4 AudioQuest units. I have (2)1200 for my JL subs. 2 are in the back of the room and 2 in the front.
AudioQuest Niagara Power conditioners
ADD-POWR Sorcer X4
Great conditioner!
AudioQuest Dragon High Current 20A for My Niagara 7000 & Dragon Source
Using this power cord on my AudioQuest Niagara 7000 power conditioner. Quite impressive!
Added another Dragon Source to my Lumin X1
Critical Mass Systems Center Stage CM2,2M in both the 1.0 & 1.5 size footers. Total of 6 sets being used.
I now have 6 sets under my equipment and boy are they impressive.
Clarus Crimson Bi-Wire Speaker Cable
Infigo Cables USB, Signature 2 sets XLR cables
Entreq Silver Tellus
Silver Tellus used om my digital. Plus a DIY large box used on analog and two smaller DIY boxes used on each speaker.
EtherRegen Uptone Audio
AfterDark Queen Clock and Linear power supply
Combo
WireWorld Platinum 8 Ethernet
I didn't think an ethernet cable would improve the sound much, but with cable connected to my Ether Regen input from my modem even though I am sending the output via fiber to my Lumin X1, increased the sound quality presence. Quite impressive.
I ordered a set of stainless steel and at the right length from a Company called Evo Industries. They made them up for me and I had them in a few days. The cost was $8 each. I don't know about Stillpoints and I am not impressed with their customer service.
I had no idea the screw adapters are so expensive. When ordering a new set of Stillpoints, can one specify the thread for free, or must one always pay extra to get the right threading? $50 per adaptor and a two month wait seems unreasonable.
Tbg, Thanks for the reply. In my case, Stillpoints wants about a $400 payment for 8 screw adapters in advance and a 2 month wait. The email replies appear quite rude to me. I don't know , for the cost of their product, I expect a little better customer service.
Ozzy, for a long time I had no experience that was bad with either the SPs Ultra SSs or Ultra Fives. Now I have had some instances where the Ultra Fives are too much.
I had great difficulty with installing SP Ultra Fives on my BMC Arcadia speakers. Previously on my Tidals, it was easy to install them as there are multiple threaded M8s holes on them and I got eight 1/4 20 to M8 adapters from StillPoints. On learning that the Arcadias had M8 threads also I simply assumed I could just move them to my new speakers. Before settting them up, I screwed them into the only four holes on the Arcadias. I did notice that the threading was far into the holes. Once I had them up I noticed that the Ultra Fives were flat against the bottom of the speakers. StillPoints doesn't encourage that saying that a small gap is better. I could not get any gape?
Later I learned that the threading on the Arcadias is from inside and that I was merely moving it further into the speakers. Fortunately, my adapters were too short to push them into the interior. I live with that situation now.
Devilboy, Sorry for the late response. The Stillpoints work great on some components and not so great on others. So my opinion is you will have to try them. The company support is pretty bad however, based on my experience in trying to get a proper adapter for my speakers.
Ozzy, how much of an improvement have the Stillpoints been? I was on the fence about purchasing three for under my components, so I went with Mapleshade's system of Isoblocks, maple platform and spikes. Just curious.
System edited: Picture added to show the different spikes I have used. First there was the original spikes with cups, then I moved to the 2" Audio Points and now I am trying the Stillpoints but I cant seem to find the right adapter .
Zephyr24069 , Thanks for the response. With my Egglestons I am also using Townsend super tweeters and a pair of JL Fanthoms F113 subs. With proper set up I now have an excellent soundstage and fantastic frequency extremes.
Yes, I took the cover off and stuck it through the opening in the circuir board tha sits atop the transformer. The transformer has a can cover over it. This weekend I will be also installing the Capacitor chips to the Pass Amp.
Ozzy, How did you install the Transformer chip on your Pass Labs , did you have to open the hood to get it on . Does it have be physically in contact with the tranny ?
Yoby, The SR Powercell 10SE comes with a Precision Reference special made 32A plug so thus far that has been the only cord I have used with the Power Conditioner. Someday I will find an adapter and then I would like to try the HiDiamond 3 on it.
Ozzy: Yes, we did. I received the Morrow Dig4 over a week ago, also with the silver Eichmans and 5 day burn in. I haven't been able to evaluate it because my computer won't download the proper driver for the usb/spdif interface that's plugged into it. Now I have to return the interface and get one that doesn't require a download. I hate this crap.
Devilboy, I believe we have communicated, but if not I apologize. Yes the Morrow cable I am using is the Dig 4, in my opinion it is way better than the Kimber D-60 in all the areas that matter. Better sound staging, sound quality, frequency extremes etc. But I did pay extra to include the Silver Eichmann rca's. The Have/Canare is a very good cable for the money and as soon as I get my Cable Cooker, I'm going to give it a try again.